About 37,200 results
Open links in new tab
  1. What is Quiescent Current and why is it important?

    Jul 13, 2019 · One very important and often overlooked specification on ICs is the Quiescent Current or IQ parameter. Quiescent Current can be defined as the amount of current used by an IC when in a …

  2. 静止電流とは何ですか、なぜ重要なのですか? - よくある質問

    Apr 7, 2020 · ICで非常に重要なのですが見過ごされがちな仕様の1つは、静止電流またはIQパラメータです。 静止電流は、静止状態のときにICが使用する電流量として定義できます。 静止状態は、IC …

  3. Quiescent current (대기 전류) > 위성방송, 위성통신, 헤드엔드 용어

    일반적인 단말기의 Quiescent current 는 100mA 안팎이며, 단말기가 기지국에서 매우 먼거리에 있을때 최대전력을 사용한다면 1A까지도 올라갈 수 있도록 되어있다. Quiescent current 는 이동단말기의 …

  4. 瞭解運算放大器電路中的功率消耗 - 產品技術提示 - DigiKey …

    Mar 7, 2024 · 運算放大器電路的功率消耗由多種因素組成,分別是靜態功率、運算放大器輸出功率和負載功率。靜態功率(或簡稱 P Quiescent)是保持放大器開啟所需的功率,規格表中一般以 I Q (靜態 …

  5. What is the purpose of the emitter bypass capacitor in the Common ...

    Jul 11, 2024 · We observe a quiescent voltage required to bias the transistor into class A service. As we apply an AC input signal, the emitter to ground voltage will vary. We can argue that the emitter …

  6. LDO 레귤레이터 선택 - 자주 묻는 질문 - DigiKey TechForum - An …

    Aug 2, 2022 · 이 게시글에서는 낮은 드롭아웃(Low-Dropout, LDO) 레귤레이터를 선택하기 위한 몇 가지 기본 요구 사항을 검토할 것입니다. 고려해야 할 다양한 요인들이 있지만, 입력 전압과 출력 전압 …

  7. 대기 전류는 무엇이며 왜 중요한가? - 자주 묻는 질문 - DigiKey …

    Jan 26, 2021 · IC에서 매우 중요하지만 간혹 간과되는 사양 중 하나가 대기 전류 또는 IQ 변수입니다. 대기 전류는 IC가 대기 상태일 때 사용하는 전류의 양으로 정의할 수 있습니다. 대기 상태는 IC가 무부하 또는 …

  8. 什麼是靜態電流? 為什麼它如此重要?

    Jun 5, 2023 · 靜態電流(或 IQ)是 IC 的一個非常重要的參數,但常常被忽視。 靜態電流可以定義為在不工作的情況下所使用的電流量。靜態是指 IC 處於空載或非開關狀態的任何一段時間,但是仍然是啟 …

  9. Opa858 - Integrated Circuits (ICs) - DigiKey TechForum - An Electronic ...

    Jan 23, 2025 · After 2-3 experiments, the quiescent current from the supply exceeds the datasheet limits, indicating possible damage. If the op-amp is replaced, it starts working fine again, with values …

  10. What is the Quiescent Operating Point for FET's? - Physics Forums

    May 22, 2012 · I was learning a lot of how to calculate the Quiescent operating point for FET's. But suddenly I got this doubt that if i am operating any transistor (BJT, FET) as a switch then I need not …